View MKP3366Y2_4524911.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MKP 336 6 Y2
Vishay BCcomponents
Interference Suppression Film Capacitors MKP Radial Potted Type
FEATURES
168x12(halfpage)
l
w
10 to 15 mm lead pitch. Supplied loose in box, taped on reel Lead (Pb)-free product
e3
RoHS
COMPLIANT
h
RoHS-compliant product
PERMISSIBLE DC VOLTAGE
lt
DC 1000 V
P 0.4
O dt
ENCAPSULATION
Plastic case, epoxy resin sealed, flame retardant UL-class 94 V - 0
Dimensions in mm
NO FOCUS PRODUCT: USE MKP 338 6 Y2 APPLICATIONS
Y2 class For Y2 electromagnetic interference suppression between line and ground applications (50/60 Hz) with a maximum mains voltage of 300 Vac. For application limitations refer to section "APPLICATION NOTES"
CLIMATIC TESTING CLASS ACC. TO EN 60068-1
55/105/56/B
CAPACITANCE RANGE (E12 SERIES)
E12 series 0.001 to 0.047 F Preferred values acc. to E6
REFERENCE STANDARDS
"IEC 60384-14 2nd edition and EN 132400" "IEC 60065 requires, pass. flamm. class B" 250 V: UL 1414; CSA-C22.2 No 1; 300 V: UL1283; ENEC
CAPACITANCE TOLERANCE
20 %; 10 %
LEADS
Tinned wire
MARKING
C-value; tolerance; rated voltage; sub-class; manufacturer's type designation; code for dielectric material; manufacturer location; year and week
MAXIMUM APPLICATION TEMPERATURE
105 C
DIELECTRIC
Polypropylene film
DETAIL SPECIFICATION
For more detailed data and test requirements contact: rfi@vishay.com
ELECTRODES
Metallized film
CONSTRUCTION
Series and triple construction
RATED VOLTAGE
AC 300 V; 50 to 60 Hz
Document Number: 28115 Revision: 12-Jul-07
For technical questions, contact: rfi@vishay.com
www.vishay.com 171
MKP 336 6 Y2
Vishay BCcomponents Interference Suppression Film Capacitors
MKP Radial Potted Type
COMPOSITION OF CATALOG NUMBER
TYPE AND PITCHES 336 6 Y2 10.0 mm 15.0 mm CAPACITANCE (numerically)
MULTIPLIER (nF) 0.1 1 2 3
Example: 103 = 10 x 1 = 10 nF
BFC2 336 6X XX X 2222(*) 336 6X XX X
(*) Old ordering code
TYPE 336 6
PACKAGING loose in box
LEAD CONFIGURATION lead length 3.5 + 1/- 0.5 mm (pitch = 10 mm) or 3.5 0.3 mm (pitch = 15 mm) lead length 25.0 2.0 mm
C-TOL 20 %
PREFERRED TYPES BFC2 336 60... BFC2 336 66... ON REQUEST
Y2
336 6 Y2
loose in box
lead length 3.5 + 1/- 0.5 mm (pitch = 10 mm) or 3.5 0.3 mm (pitch = 15 mm) lead length 25.0 2.0 mm H = 18.5 mm; P0 = 12.7 mm; reel diameter 500 mm
10 % 20 % 10 %
BFC2 336 61... BFC2 336 67... BFC2 336 63... BFC2 336 64...
taped on reel (1)
Note: (1) For detailed tape specification refer to Packaging information: www.vishay.com/docs/28139/packinfo.pdf
SPECIFIC REFERENCE DATA MKP 336 6 300 VAC
DESCRIPTION Tangent of loss angle: VALUE at 10 kHz 10 x 10 -4 Rated voltage pulse slope (dU/dt)R at 420 V (DC) R between leads, for C 0.33 F at 100 V; 1 minute R between leads and case; 100 V; 1 minute Withstanding (DC) voltage (cut off current 10 mA); rise time 100 V/s Withstanding (AC) voltage between leads and case 200 V/s > 15 000 M > 30 000 M 3400 V; 1 minute 2100 V; 1 minute
www.vishay.com 172
For technical questions, contact: rfi@vishay.com
Document Number: 28115 Revision: 12-Jul-07
MKP 336 6 Y2
Interference Suppression Film Capacitors Vishay BCcomponents MKP Radial Potted Type
MKP 336 6 GENERAL DATA
URac = 300 V; C-tol = 20 %
CATALOG NUMBER BFC2 336 6..... AND PACKAGING LOOSE IN BOX C (F) DIMENSIONS WxHxL (mm) MASS (g)(1) Lt = 3.5 + 1/- 0.5 mm (10 mm) or 3.5 03 mm (= 15 mm) Last 5 digits of catalog number Pitch = 10.0 0.4 mm; dt = 0.6 0.06 mm 0.001 0.0015 0.0022 0.0033 0.0047 0.0068 5.0 x 11.0 x 12.5 0.82 4.0 x 10.0 x 12.5 0.6 60102 60152 60222 60332 60472 60682 1000 66102 66152 66222 66332 66472 66682 1000 1250 63102 63152 63222 63332 63472 63682 1100 1400 SPQ lt = 25.0 2.0 mm Last 5 digits of catalog number SPQ REEL H = 18.5 mm; P0 = 12.7 mm Last 5 digits of catalog number SPQ
Pitch = 15.0 0.4 mm; dt = 0.6 0.06 mm 0.0068 0.01 0.015 5.0 x 11.0 x 17.5 6.0 x 12.0 x 17.5 1.0 1.4 69005 60103 60153 1000 69009 66103 66153 1000 69006 63103 63153 1100 900
Pitch = 15.0 0.4 mm; dt = 0.8 0.08 mm 0.022 0.033 0.047 Notes (1) Weight for short lead product only. 7.0 x 13.5 x 17.5 8.5 x 15.0 x 17.5 10.0 x 16.5 x 17.5 1.8 2.4 3.0 60223 60333 60473 750 500 66223 66333 66473 500 450 63223 63333 63473 800 650 600
Document Number: 28115 Revision: 12-Jul-07
For technical questions, contact: rfi@vishay.com
www.vishay.com 173
MKP 336 6 Y2
Vishay BCcomponents Interference Suppression Film Capacitors
MKP Radial Potted Type
MKP 336 6 GENERAL DATA
URac = 300 V; C-tol = 10 %
CATALOG NUMBER BFC2 336 6..... AND PACKAGING LOOSE IN BOX C (F) DIMENSIONS WxHxL (mm) MASS (g)(1) Lt = 3.5 + 1/- 0.5 mm (10 mm) or 3.5 03 mm (= 15 mm) Last 5 digits of catalog number Pitch = 10.0 0.4 mm; dt = 0.6 0.06 mm 0.001 0.0012 0.0015 0.0018 0.0022 0.0027 0.0033 0.0039 0.0047 0.0056 5.0 x 11.0 x 12.5 1.1 4.0 x 10.0 x 12.5 0.6 61102 61122 61152 61182 61222 61272 61332 61392 61472 61562 1000 1000 67102 67122 67152 67182 67222 67272 67332 67392 67472 67562 1000 1250 64102 64122 64152 64182 64222 64272 64332 64392 64472 64562 1100 1400 SPQ lt = 25.0 2.0 mm Last 5 digits of catalog number SPQ REEL H = 18.5 mm; P0 = 12.7 mm Last 5 digits of catalog number SPQ
Pitch = 15.0 0.4 mm; dt = 0.80 0.08 mm 0.0056 0.0068 0.0082 0.01 0.012 0.015 6.0 x 12.0 x 17.5 1.4 5.0 x 11.0 x 17.5 1.0 69001 61682 61822 61103 61123 61153 61183 1000 1000 69007 67682 67822 67103 67123 67153 67183 1000 1000 69003 64682 64822 64103 64123 61153 64183 900 1100
0.018 Pitch = 15.0 0.4 mm; dt = 0.80 0.08 mm 0.022 0.027 0.033 0.039 0.047 Notes (1) Weight for short lead product only. 7.0 x 13.5 x 17.5 8.5 x 15.0 x 17.5 10.0 x 16.5 x 17.5 1.8 2.4 3.0
61223 61273 61333 61393 61473 500 750
67223 67273 67333 67393 67473 450 500
64223 64273 64333 61393 64473
800 650 600
www.vishay.com 174
For technical questions, contact: rfi@vishay.com
Document Number: 28115 Revision: 12-Jul-07
MKP 336 6 Y2
Interference Suppression Film Capacitors Vishay BCcomponents MKP Radial Potted Type
SAFETY APPROVALS Y2 EN132400 UL1414 and CSA-C 22.2 No 1 antenna coupling UL1283 VOLTAGE 300 V (AC) 250 V (AC) 300 V (AC) VALUE 1 nF to 47 nF 1 nF to 47 nF 1 nF to 47 nF FILE NUMBERS FI 2006018 E112471 E109565
The Enec-approval together with the CB-Certificate replace all national marks of the following countries (they have already signed the ENEC-Agreement): Austria; Belgium; Czech. Republic; Denmark; Finland; France; Germany; Greece; Hungary; Ireland; Italy; Luxembourg; Netherlands; Norway; Portugal; Slovenian; Spain; Switzerland and United Kingdom.
16
MOUNTING
Normal Use The capacitors are designed for mounting on printed-circuit boards. The capacitors packed in bandoliers are designed for mounting in printed-circuit boards by means of automatic insertion machines. Specific Method of Mounting to Withstand Vibration and Shock In order to withstand vibration and shock tests, it must be ensured that the stand-off pips are in good contact with the printed-circuit board: * The capacitors shall be mechanically fixed by the leads Space Requirements on printed Circuit Board The maximum length and width of film capacitors is shown in Figure: * Eccentricity as in figure. The maximum eccentricity is smaller than or equal to the lead diameter of the product concerned * Product height with seating plane as given by "IEC 60717" as reference: hmax h + 0.3 mm
bmax = b + 0.3 mm eccentricity
lmax = I + 0.3 mm
CBA116
Storage Temperature * Storage temperature: Tstg = 25 to + 40 C with RH maximum 80 % without condensation Ratings and Characteristics Reference Conditions Unless otherwise specified, all electrical values apply to an ambient temperature of 23 1 C, an atmospheric pressure of 86 to 106 kPa and a relative humidity of 50 2 %. For reference testing, a conditioning period shall be applied over 96 4 hours by heating the products in a circulating air oven at the rated temperature and a relative humidity not exceeding 20 %.
Document Number: 28115 Revision: 12-Jul-07
For technical questions, contact: rfi@vishay.com
www.vishay.com 175
MKP 336 6 Y2
Vishay BCcomponents Interference Suppression Film Capacitors
MKP Radial Potted Type
CHARACTERISTICS
Capacitance
4
Tangent of loss angle
10
3
C/C (%)
2
typical
0
-2
Dissipation Factor (x 10- 4)
10 2
101
-4
min.
F 47 n C F< 10 n 10 nF C
-6 - 50 0 50 Tamb (C) 100
10
0
10
1
10
2
10
3
10
4
f (Hz) 10 5
Impedance
103 Impedance ()
1n 4.7 10
47
Resonant frequency
F
102 f (MHz) 101 100 1 10 47
nF
nF
10
1
nF
100
10-1
10-2 104 105 106 107
f (Hz) 108
C (nF)
Max RMS voltage and AC current (sinewave)
10
3
10 3
AC voltage (V)
AC current (mA)
47 nF
102
10 1
10 nF 4.7 nF
10 0
1nF
Tamb 105 C 101 10
1
10
-1
Tamb 105 C 10 1 10 2 10 3 104 f (Hz) 105
10
2
10
3
10
4
f (Hz) 105
www.vishay.com 176
For technical questions, contact: rfi@vishay.com
Document Number: 28115 Revision: 12-Jul-07
MKP 336 6 Y2
Interference Suppression Film Capacitors Vishay BCcomponents MKP Radial Potted Type
Insulation resistance
10
6
RC (s)
10
5
10
4
0
20
40
60
80 T 100 amb(C)
APPLICATION NOTES
* For Y2 electromagnetic interference suppression between line and ground (50/60 Hz) with a maximum mains voltage of 300 V (AC) 10 % instability. * These capacitors are not intended for continuous pulse applications. For these situations, capacitors of the AC and pulse program must be used. * The maximum ambient temperature must not exceed 105 C. * Rated voltage pulse slope: If the pulse voltage is lower than the rated voltage, the values of the specific reference data can be multiplied by 420 V (DC) and divided by the applied voltage.
Document Number: 28115 Revision: 12-Jul-07
For technical questions, contact: rfi@vishay.com
www.vishay.com 177
MKP 336 6 Y2
Vishay BCcomponents Interference Suppression Film Capacitors
MKP Radial Potted Type
INSPECTION REQUIREMENTS General Notes: 1. Sub-clause numbers of tests and performance requirements refer to the " Sectional Specification, IEC-puplication EN 132400 (IEC 60384-14) and section One of this specification". 2. In this table: D =destructive ND = non destructive
Group C inspection requirements
SUB - CLAUSE NUMBER AND TEST D OR ND
CONDITIONS
PERFORMANCE REQUIREMENTS
Group C inspection (periodic) see section "General notes" item 3 SUB-GROUP C1A PART OF SAMPLE OF SUB-GROUP C1 4.1 Dimensions (detail) Initial measurements 4.3 Robustness of terminations 4.4 Resistance to soldering heat Capacitance Tangent of loss angle at 10 kHz Tensile: load 10 N; 10 s Bending: load 5 N; 4 x 90 No pre-drying Method: 1A Solder bath: 260 C Duration: 10 s Isopropylalcohol at room temperature Method: 2 Immersion time: 5 0.5 min Recovery time: Min 1 hour, max 2 hours Visual examination Capacitance Tangent of loss angle No visible damage Legible marking |C/C| 5 % of the value measured initially Increase of tan : 0.008 Compared to values measured initially As specified in Section "Insulation Resistance" of this specification No visible damage D As specified in Chapters "General data" of this specification
4.19 Component solvent resistance
4.4.2 Final measurements
Insulation resistance SUB - GROUP C1B PART OF SAMPLE OF SUB - GROUP C1 Initial measurements 4.20 Solvent resistance of the marking: see Section "General notes"; item 5 D Capacitance Tangent of loss angle at 10 kHz Isopropylalcohol at room temperature Method: 1 Rubbing material: cotton wool Immersion time: 5 0.5 min A = - 55 C B = + 105 C 5 cycles Duration t = 30 min
No visible damage Legible marking
4.6 Rapid change of temperature
4.6.1 Inspection
www.vishay.com 178
For technical questions, contact: rfi@vishay.com
Document Number: 28115 Revision: 12-Jul-07
MKP 336 6 Y2
Interference Suppression Film Capacitors Vishay BCcomponents MKP Radial Potted Type
SUB - CLAUSE NUMBER AND TEST 4.7 Vibration (see note 3) D OR ND
CONDITIONS Visual examination Mounting: see Section "Mounting" of this specification Procedure B4 Frequency range: 10 to 55 Hz. Amplitude: 0.75 mm or Acceleration 98 m/s (whichever is less severe) Total duration 6 hours. Visual examination Mounting: see Section "Mounting" for more information Pulse shape: half sine Acceleration: 490 m/s Duration of pulse: 11 ms. Visual examination Capacitance Tangent of loss angle
PERFORMANCE REQUIREMENTS No visible damage
4.7.2 Final inspection 4.9 Shock (see note 3)
No visible damage
4.9.2 Final measurements
No visible damage |C/C| 5 % of the value measured initially Increase of tan : 0.008 Compared to initially
values
measured
Insulation resistance SUB - GROUP C1 COMBINED SAMPLE OF SPECIMENS OF SUB GROUPS C1A AND C1B 4.11 Climatic sequence 4.11.1 Initial measurements Capacitance Measured in 4.4.2 and 4.9.2 Tangent of loss angle: Measured initially in C1A and C1B Temperature: 105 C Duration: 16 hours
As specified in Section "Insulation Resistance" of this specification
D
4.11.2 Dry heat 4.11.3 Damp heat cyclic Test Db First cycle 4.11.4 Cold 4.11.5 Damp heat cyclic Test Db remaining cycles 4.11.6 Final measurements
Temperature: - 55 C Duration: 2 hours
Visual examination
No visible damage Legible marking |C/C| 5 % of the value measured in 4.11.1. Increase of tan : 0.008 Compared to values measured in 4.11.1. No permanent breakdown or flash-over 50 % of values specified in Section "Insulation resistance" of this specification
Capacitance
Tangent of loss angle
Voltage proof 2250 V (DC); 1 min between term. Insulation resistance
Document Number: 28115 Revision: 12-Jul-07
For technical questions, contact: rfi@vishay.com
www.vishay.com 179
MKP 336 6 Y2
Vishay BCcomponents Interference Suppression Film Capacitors
MKP Radial Potted Type
SUB - CLAUSE NUMBER AND TEST SUB - GROUP C2 4.12 Damp heat steady state D OR ND D 56 days, 40 C, 90 to 95 % RH no load capacitance CONDITIONS PERFORMANCE REQUIREMENTS
4.12.1 Initial measurements
Capacitance Tangent of loss angle at 10 kHz
4.12.3 Final measurements
Visual examination
No visible damage Legible marking |C/C| 5 % of the value measured in 4.12.1. Increase of tan : 0.007 Compared to values measured in 4.12.1. No permanent breakdown or flash-over
Capacitance
Tangent of loss angle
Voltage proof 2250 V (DC); 1 min between term.
Insulation resistance
50 % of values specified in Section "Insulation resistance" of this specification
SUB- GROUP C3 4.13.1 Initial measurements
D Capacitance Tangent of loss angle at 10 kHz 3 successive impulses, full wave, peak voltage: 5 kV Max. 24 pulses No selfhealing breakdowns or flashover
4.13 Impulse voltage
4.14 Endurance
Duration: 1000 hours 1.7 URac at 105 C Once in every hour the voltage is increased to 1000 V (RMS) for 0.1 s via resistor of 47 5 % Visual examination No visible damage Legible marking |C/C| 10 % compared to values measured in 4.13.1. Increase of tan : 0.007 Compared to values measured in No permanent breakdown or flash-over 1 min between
4.14.7 Final measurements
Capacitance
Tangent of loss angle
Voltage proof 2250 V (DC); terminations. Insulation resistance
50 % of values specified in Section "Insulation resistance" of this specification
www.vishay.com 180
For technical questions, contact: rfi@vishay.com
Document Number: 28115 Revision: 12-Jul-07
MKP 336 6
Interference Suppression Film Capacitors MKP Radial Potted Type
SUB - CLAUSE NUMBER AND TEST SUB - GROUP C 4 4.15 Charge and discharge D OR ND D 10 000 cycles (50 c/s) charge to UR half sinewave Duration: 5 ms Discharge resistance: 420 Vdc R = -------------------------------------------------1.5 x C ( ( dU ) ( dt ) ) Rmin = 2.2 4.15.1 Initial measurements 4.15.3 Final measurements Capacitance Tangent of loss angle at 10 kHz Capacitance Tangent of loss angle |C/C| 10 % compared to values measured in 4.15.1. Increase of tan : 0.008 Compared to values measured in 4.15.1. 50 % of values specified in Section "Insulation resistance" of this specification As specified in Section "Resonant frequency" of this specification. 10 % After removing test flame from capacitor, the capacitor must not continue to burn for more than 10 s. No burning particle must drop from the sample.
Vishay BCcomponents
CONDITIONS
PERFORMANCE REQUIREMENTS
Insulation resistance
SUB - GROUP C5 4.16 Radio frequency characteristic SUB - GROUP C6 4.17 Passive flammability Class B
D Resonance frequency D Bore of gas jet: O 0.5 mm Fuel: butane Test duration for actual volume V in mm: V 250: 10 s 250 < V 500: 20 s 500 < V 1750: 30 s V > 1750: 60 s One flame application
12 mm ~ 8 mm
45.0
SUB - GROUP C7 4.18 Active flammability
D 20 x 5 kV discharges on the test capacitor connected to UR The cheese cloth around the capacitors shall not burn with a flame. No electrical measurements are required.
Document Number: 28115 Revision: 12-Jul-07
For technical questions, contact: rfi@vishay.com
www.vishay.com 181
Legal Disclaimer Notice
Vishay
Disclaimer
All product specifications and data are subject to change without notice. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, "Vishay"), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein or in any other disclosure relating to any product. Vishay disclaims any and all liability arising out of the use or application of any product described herein or of any information provided herein to the maximum extent permitted by law. The product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein, which apply to these products. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications unless otherwise expressly indicated. Customers using or selling Vishay products not expressly indicated for use in such applications do so entirely at their own risk and agree to fully indemnify Vishay for any damages arising or resulting from such use or sale. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. Product names and markings noted herein may be trademarks of their respective owners.
Document Number: 91000 Revision: 18-Jul-08
www.vishay.com 1

▲Up To Search▲

Price & Availability of MKP3366Y2

	To Download MKP3366Y2 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .